Changing a power tools voltage ?

May 9, 2010 by admin · 1 Comment
Filed under: Engineering 
power tools
David firth asked:

I have a Festool TS75 which is 110 volts. What would i need to change inside the saw so it works on 230 volts.

Related Blogs

  • Related Blogs on Power Tools

When using power tools with electrical cords, remember to?

May 6, 2010 by admin · 1 Comment
Filed under: Engineering 
power tools
Stephani asked:

A. Keep cords and hoses away from heat, oil, and sharp objects

B. Only carry portable tools by the cord if they are shut off

C. Hoist or lower tools by electrical cords that are in good condition only

Related Blogs

Related Blogs

How do I correctly connect a piece of EL Wire to another wire that is connected to the power souce.Sodder gun?

April 6, 2010 by admin · 1 Comment
Filed under: Engineering 
power tools
my frenn jenn asked:

I purchased the EL Wire @ Vibelights.Com, but no instructions came with my package. I have a 30′ piece of EL Wire that I want to cut into a few pieces and connect seperate power sources to each one - I just dont know where to start or with what tools.

Related Blogs

Related Blogs

can a 10,000 watt power inverter power an air compressor of 3hp?

March 22, 2010 by admin · 4 Comments
Filed under: Engineering 
power tools
Daniel P asked:

i dont have a garage and want to do projects with my truck. I am planning to use power tools such as grinders, and most especially an air compressor that can supply enough power to paint a car. i know i can put up light bulbs with any power inverter but vaccuums and other power tools that have moving parts, even if their rating is well below the rating of my inverter does not work, why and how can i solve this problem?

Related Blogs

  • Related Blogs on Power Tools

Related Blogs

  • Related Blogs on Power Tools

Can a 110 volt power tool be wired to work on 220v 50 mghz?

March 17, 2010 by admin · 5 Comments
Filed under: Engineering 
power tools
carpenter asked:

I’m moving to Philippines and would like to be able to use my tools there. They don’t have 110 volt electricity like here.

Related Blogs

  • Related Blogs on Tools

Related Blogs

  • Related Blogs on Tools

How do you measure power output during electrical generation?

March 2, 2010 by admin · 5 Comments
Filed under: Engineering 
power tool
ez_porsche asked:

I’m measuring the amount of power produced by different types of electrical generation for my science fair project, and I need a tool to measure it. What should I use?

Related Blogs

Related Blogs

how do i make the tools to pick a lock without powertools only house hold products?

February 18, 2010 by admin · 3 Comments
Filed under: Engineering 
power tools
hihime1234 asked:

i dont have power tools

Related Blogs

  • Related Blogs on Power Tools

Related Blogs

  • Related Blogs on Power Tools

how do i make the tools to pick a lock without powertools only house hold products?

February 16, 2010 by admin · 3 Comments
Filed under: Engineering 
power tools
hihime1234 asked:

i dont have power tools

Related Blogs

  • Related Blogs on Power Tools

Related Blogs

What type of power tool(s) are these? (pic inside)?

February 8, 2010 by admin · 2 Comments
Filed under: Engineering 
power tool
Lisa asked:

I went to a steel fabricator but I wasn’t able to catch all the descriptions of the tools used for cutting, welding, drilling holes, etc.
(1) Is this an oxy torch or a welder? It cut through heavy steel. (http://img24.imageshack.us/img24/7809/dsc00995o.jpg)

(2) What is this called? I know it cuts through steel too. (http://img24.imageshack.us/img24/39/dsc01021d.jpg)

Thanks.

Related Blogs

  • Related Blogs on Steel Fabricator

Related Blogs

  • Related Blogs on Steel Fabricator

Any extra safety concerns regarding electricity when using a power tool driven by a generator?

February 4, 2010 by admin · 4 Comments
Filed under: Engineering 
power tool
tomcat asked:

I mean, a portable petrol operated generator has no earth rod in the ground.

Related Blogs

Related Blogs

« Previous PageNext Page »